[simpits-tech] Dzus layout drawing...

[biggles]

Thanks Erwin,

Time for a visit :)

Biggles.
  ----- Original Message ----- 
  From: Erwin Neyt 
  To: 'Simulator Cockpit tech list' 
  Sent: Tuesday, March 23, 2004 7:40 PM
  Subject: RE: [simpits-tech] Dzus layout drawing...


  Rene,

  If you're interested, Pim has one you might want to check out.

  Erwin.



----------------------------------------------------------------------------
    From: simpits-tech-bounces at simpits.org [mailto:simpits-tech-bounces at simpits.org] On Behalf Of biggles
    Sent: Tuesday, March 23, 2004 3:05
    To: Simulator Cockpit tech list
    Subject: Re: [simpits-tech] Dzus layout drawing...


    David,

    Is it possible to post a picture of the tool ?
    Might be a way to make one myself ?
    Or is it some kind of fancy technical devise ?

    Thanks,

    Biggles.
      ----- Original Message ----- 
      From: Joseph Fagner 
      To: 'Simulator Cockpit tech list' 
      Sent: Tuesday, March 23, 2004 2:04 AM
      Subject: RE: [simpits-tech] Dzus layout drawing...


      So there is a special tool that presses those little quarter turn fastener into the back plates, no?

       

      This is good stuff, there's a bunch of us over at Viperpits getting plans together to make our own back lit panels.  What's the info I need on the hole sizes and stuff like that?  I already know the hole spacing, from this discussion, but David, you were referring to a coutersind cage and piloted cutter.  What are those guys?  I might get that myself and do all the holes for the groups back plates.

       

      Jay

       

      -----Original Message-----
      From: simpits-tech-bounces at simpits.org [mailto:simpits-tech-bounces at simpits.org] On Behalf Of David C. Allen
      Sent: Monday, March 22, 2004 5:01 PM
      To: Simulator Cockpit tech list
      Subject: Re: [simpits-tech] Dzus layout drawing...

       

      At 03:33 PM 3/22/2004, you wrote:

      > > >I'm not going to countersink the holes since I refuse to pay $300 for a

      > > >very simple tool.

      > >

      > > Gene

      > > You can buy a used Aircraft Microstop Countersink Cage and a new 100 degree

      > > piloted cutter from Ray Lawrence, email  RL100W at aol.com for around $35.00.

      > > Just get a piloted cutter for the .257 hole.

      > >

      > 

      >I was referring to the dzus press.  Is that it?

       

      Gene

      No that was for the micro-stop and counter sink

       

      But if you want to send me the Dzus fasteners and the panels, I will use my 

      Dzus tool and press them in for you.

       

      David

       

      >g.

      > 

      > 

      >_______________________________________________

      >Simpits-tech mailing list

      >Simpits-tech at simpits.org

      >http://www.simpits.org/mailman/listinfo/simpits-tech

      >To unsubscribe, please see the instructions at the bottom of the above 

      >page.  Thanks!

       

      _______________________________________________

      Simpits-tech mailing list

      Simpits-tech at simpits.org

      http://www.simpits.org/mailman/listinfo/simpits-tech

      To unsubscribe, please see the instructions at the bottom of the above page.  Thanks!



--------------------------------------------------------------------------


      _______________________________________________
      Simpits-tech mailing list
      Simpits-tech at simpits.org
      http://www.simpits.org/mailman/listinfo/simpits-tech
      To unsubscribe, please see the instructions at the bottom of the above page.  Thanks!


------------------------------------------------------------------------------


  _______________________________________________
  Simpits-tech mailing list
  Simpits-tech at simpits.org
  http://www.simpits.org/mailman/listinfo/simpits-tech
  To unsubscribe, please see the instructions at the bottom of the above page.  Thanks!
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.simpits.org/pipermail/simpits-tech/attachments/20040324/73c6d466/attachment.html