[simpits-tech] Dzus layout drawing...

[Gene Buckle]

Thanks Erwin.  Unfortunately, it's the rail spacing I'm after, not the
hole spacing on the rail.  It's a useful upload though!

g.


On Mon, 22 Mar 2004, Erwin Neyt wrote:

> Maybe this helps....
>
> Link: http://www.simpits.org/fileproc/dload.php?file=pr35.jpg
>
> Erwin
>
> > -----Original Message-----
> > From: simpits-tech-bounces at simpits.org
> > [mailto:simpits-tech-bounces at simpits.org] On Behalf Of Gene Buckle
> > Sent: Monday, March 22, 2004 20:51
> > To: Simulator Cockpit tech list
> > Subject: Re: [simpits-tech] Dzus layout drawing...
> >
> > Thanks for the info Dave.  Unfortunately, I don't have any
> > mechanical drawings that cover the side consoles in the
> > Eagle.  Would measuring from retaining wire to retaining wire
> > be good enough to tell me what the spacing is?
> >
> > tnx!
> >
> > g.
> >
> >
> > On Mon, 22 Mar 2004, David C. Allen wrote:
> >
> > > Hi Gene
> > > Look for the center to center specification of your Dzus mounting
> > > rails that you are going to install the panels in. Sorry for the
> > > confusion but unless we find a Mil-Spec or ATA Spec, all I
> > have is this information:
> > >
> > > Here is a Real Life Panel Example for a 5.75 x 9.00 nominal panel.
> > > Using the lower left hand corner as the controlling edges:
> > >
> > > Panel width from the Left controlling edge 5.750 +0.000
> > -0.020 Panel
> > > height from the Bottom controlling edge 9.000 +0.000 -0.041
> > >
> > > Dzus hole location: +/- .005"
> > > 0.183 from the Left controlling edge to the first Dzus centerline
> > > 5.548 from the Left controlling edge to the second Dzus centerline
> > >
> > > Nominal  5.365 between the first and second Dzus centerlines
> > >
> > > First & second Dzus centerline 0.554 up from the lower controlling
> > > edge
> > >
> > > The third and fourth Dzus centerline would be located 8.429 up from
> > > the lower controlling edge.
> > >
> > > As you can see the "Top Edge" and "Right Edge" float with
> > the tolerance.
> > > The Dzus dimensions are held to +/- 005"
> > >
> > > David
> > >
> > > At 11:18 AM 3/22/2004, you wrote:
> > >
> > > >Ok, who's right?  I gotta know for sure before I send off the data
> > > >for metal plates to be drilled. :)
> > > >
> > > >g.
> > > >
> > > >
> > > >_______________________________________________
> > > >Simpits-tech mailing list
> > > >Simpits-tech at simpits.org
> > > >http://www.simpits.org/mailman/listinfo/simpits-tech
> > > >To unsubscribe, please see the instructions at the bottom of the
> > > >above page.  Thanks!
> > >
> > > _______________________________________________
> > > Simpits-tech mailing list
> > > Simpits-tech at simpits.org
> > > http://www.simpits.org/mailman/listinfo/simpits-tech
> > > To unsubscribe, please see the instructions at the bottom
> > of the above page.  Thanks!
> > >
> >
> > _______________________________________________
> > Simpits-tech mailing list
> > Simpits-tech at simpits.org
> > http://www.simpits.org/mailman/listinfo/simpits-tech
> > To unsubscribe, please see the instructions at the bottom of
> > the above page.  Thanks!
> >
>
> _______________________________________________
> Simpits-tech mailing list
> Simpits-tech at simpits.org
> http://www.simpits.org/mailman/listinfo/simpits-tech
> To unsubscribe, please see the instructions at the bottom of the above page.  Thanks!
>