[simpits-tech] May the Force Feedback be with you...
Akin, Keenan L
simpits-tech@simpits.org
Mon, 10 Feb 2003 07:41:08 -0600
Hey! I think Marv is on to something! Maybe I can find a wind tunnel on eBay....
Keenan
-----Original Message-----
From: Marv De Beque [mailto:mdebeque@woh.rr.com]
Sent: Monday, February 10, 2003 4:21 AM
To: simpits-tech@simpits.org
Subject: Re: [simpits-tech] May the Force Feedback be with you...
IF YOU REALLY WANT TO DO IT RIGT---
Build a full size aircraft with all the control surfaces and put a giant
speed controlled fan in front of it. ;-)
On 2/10/03 12:08 AM, "Matt Bailey" <mattb@rtccom.net> wrote:
> Why bother with the extra trim cylinder? Just use one assembly, for force,
> and move it with, say, a rack and pinion. A reeaally neat way to do this
> would be to link a trim wheel to the rack and pinion, and connect a two-way
> motor/servo to the wheel........with the forward/off/aft switch mounted on
> the control stick/yoke. Then you have mechanical and electric trim available,
> bypassing software completely. Sweeet. :)
>
> -Matt Bailey
>
> On Sunday 09 February 2003 23:44, you wrote:
>> ive added labels to my drawing for bigger clarity..
>>
>> the problem of using one cylinder to handle both trim (center offset)
>> and stick pressure is much the same as with a spring...
>>
>> say total is 20 units (that could be liters, PSI, bar pressure - what
>> ever, it doesn't matter in this discustion..
>> center is then C1A=10 and C1B=10
>>
>> if you are out of balance (wrong trim) and C1A=15 and C1B=5 it would be
>> much easier to move the pistone 1inch and compress C1A than to compress
>> C1B... but if you use Cylinder1 (=3 in my drawing, a little typo) to
>> only control the pressure needed to move the stick things will get a lot
>> simpler - more pressure in both C1A and C1B the harder it will be to
>> move the stick.
>>
>> the reason for using to valves (V1 and V2) and not just putting C1A and
>> C1B on the same hose is; the stick will just move air from one chamber
>> to the other.
>>
>>
>>
>> with cylinder 2 you can control the center of the stick - hence the trim
>> possition. if you put more pressure into C2A the stick will go backward,
>> in effect you can contol where the netural stick possition is.....
>>
>>
>> with regard to pressure needed to control the stick...
>>
>> you could probaly get a sping loaded system to work, but as Craig
>> mentioned, there are afew conditions where it will get into trouble...
>> namely :
>>
>> 1) no movement (here you could with my schematics just open V1 and V2
>> and you would have no resistance what so ever)
>>
>> 2) high G turn where the force required to pull stick either backwards
>> is greater then moving the stick forward (with my schematics this can be
>> done by applying more pressure to C1B (and C2A to keep the netual
>> possition)
>>
>> 3) very low G turn - the oposit of 2
> _______________________________________________
> Simpits-tech mailing list
> Simpits-tech@simpits.org
> http://www.simpits.org/mailman/listinfo/simpits-tech
> To unsubscribe, please see the instructions at the bottom of the above page.
> Thanks!
_______________________________________________
Simpits-tech mailing list
Simpits-tech@simpits.org
http://www.simpits.org/mailman/listinfo/simpits-tech
To unsubscribe, please see the instructions at the bottom of the above page. Thanks!