<div dir="ltr"><div><div><div>Update to <span class="gmail-im">getting the N1 & N2 gauges operational?<br><br></span></div><span class="gmail-im">Found the part number, for the </span><span class="gmail-im">N1/N2 tach generator, and found one on eBay for $25<br>Hooked it up to a drill motor to look at the output amplitude and frequency. This also allowed me to check my N1/N2 gauges for operation. Found 2 bad ones.<br><br></span></div><span class="gmail-im">Looks like generating </span><span class="gmail-im">sine wave approach that used the Arduino's PWM channels is the one I will try.<br><br></span></div><span class="gmail-im">David<br></span><div><span class="gmail-im"><br></span><div><span class="gmail-im"></span></div></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Aug 7, 2017 at 1:53 PM, Matt Bailey <span dir="ltr"><<a href="mailto:dabigboy@cox.net" target="_blank">dabigboy@cox.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div><div>It's pretty straightforward. You can do this with just an Arduino and one of the cheapo L298N H-bridge boards on ebay. I did it very crudely and easily, and ended up with poor control below about 30% RPM (on my particular indicator), but totally smooth response above that. Another fellow I know adapted a sine wave approach that used the Arduino's PWM channels, which gave good control all the way down to 0.</div><div><br></div><div>Check out the overhaul manual for your indicators. You're basically building a brushless speed controller.</div><div><br></div><div>Matt</div><div><br></div><div><br></div><div><br></div><div id="m_-5876426192730443451composer_signature"><div style="font-size:85%;color:#575757">Sent from my Sprint Samsung Galaxy S® 6.</div></div><span class=""><div style="font-size:100%;color:#000000"><div>-------- Original message --------</div><div>From: "David C. Allen" <<a href="mailto:dca911t@gmail.com" target="_blank">dca911t@gmail.com</a>> </div><div>Date: 8/7/2017  1:04 PM  (GMT-06:00) </div><div>To: Simulator Cockpit Builder's List <<a href="mailto:simpits-tech@simpits.org" target="_blank">simpits-tech@simpits.org</a>> </div><div>Subject: [simpits-tech] N1 & N2 Gauges </div><div><br></div></div></span><div dir="ltr"><div><div><div><div><div><div><div><span class=""><div><div>Hello<br></div>I was wondering if anyone has used a Arduino to get the N1 & N2 gauges operational?<br><br></div></span><span class="">From the information I have found there is a 3 phase generator for the N1 & N2 mounted on the engine. The gauges have a 3 phase motor connected to a flux coupling (like is used in a mechanical speedometer) to drive the pointer. Once the engine is operating the N1 & N2 are self powered.<br><br></span></div><span class="">I found a chart that lists the generator RPM vs Indicator % RPM<br><br></span></div><span class="">0 gen = 0 %RPM<br>840 gen = 20 %RPM<br>2520 gen = 60 %RPM<br>4200 gen = 100 %RPM<br><br></span></div><span class="">So a question on frequency of the generator, would vary with generator RPM <br><br></span></div><span class="">Looking at one leg of the generator <br><br>0 gen = 0 Hz = 0 %RPM<br>840 gen = 14 Hz = 20 %RPM<br>2520 gen = 42 Hz = 60 %RPM<br>4200 gen = 70 Hz = 100 %RPM<br><br></span></div>Just looking for ideas<br><br></div>David<br></div>N9070U 737-222<br></div>
</div><br>______________________________<wbr>_________________<br>
Simpits-tech mailing list<br>
<a href="mailto:Simpits-tech@simpits.org">Simpits-tech@simpits.org</a><br>
<a href="http://www.simpits.org/mailman/listinfo/simpits-tech" rel="noreferrer" target="_blank">http://www.simpits.org/<wbr>mailman/listinfo/simpits-tech</a><br>
To unsubscribe, please see the instructions at the bottom of the above page.  Thanks!<br></blockquote></div><br></div>